Wheels

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits Campagnolo / Italian rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 26tpi - Diameter: 10mm - Length: 146mm - 1 axle per bag

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

Use Stan's Tubeless Valve Stems when you're converting standard rims to tubeless via the taping method. These also have a removable core for easier application of tire sealant. Note: Schrader valve is for non-stepped Hugo rims. If your Hugo rim decal reads: - MAX RIM PRESSURE: 2.8 tires: 26psi, 3.0 tires: 24psi - ERD 615, 622x49.9, 29 in x 52.3mm Your rim has a stepped valve and is not compatible with this Schrader valve.

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - Compatible with straight pull hubs only - One 264mm spoke = 5.9g - Nipples sold separately

The buyer's choice for wheel builders looking to save weight. ProLock nipples contain a special adhesive compound (by Loctite) which is activated when a spoke is threaded into the nipple, forming a durable bond. - 32 nipples weigh approximately 30 grams

These original replacements will get your wheels working like new. - Alloy thru-axle that can be used with a 6mm hex wrench or with a lever - Keep it light by removing the lever and instead use a 6mm hex wrench - Keep it convenient by keeping the lever inside the axle - Lever is held securely by internal O-ring - Lever sold separately

To be used exclusively with Bontrager Tubeless Ready (TLR) rims. The rim strips you need to upgrade to Tubeless These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Product details - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Use only with appropriate Bontrager TLR rim valve - Rim strip replacement is recommended if removed from the wheel - Sold as singles - White strip is recommended for carbon rims - TLR rim valve sold separately

These rim strips are crucial in upgrading your Tubeless Ready (TLR) Bontrager wheels to the next level of dependability and performance. Key features: - To be used exclusively with Bontrager 29"/700c Tubeless Ready (TLR) wheels - TLR Rim Strips are the light and easy solution to Bontrager Tubeless conversion - Rim Strip replacement is recommended if removed from the wheel - For specific compatibility, access 'WHEELS' tab on the Tech Site or contact Customer Service

Includes rim strip and tubeless tape for 1 wheel.

Wheel Conversion Caps for Zipp 77/177 Disc hubs. Converts your Zipp 77 or 177 hubs to nearly any frame standard.

These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

- Hub axle end cap set, rear - Zipp Cognition V2 Rim Brake - Quick release

The Wolf Tooth axle uses a captive steel washer under the head to reduce friction on the fork leg. This protects your expensive fork, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. These are also a great replacement option for lost or damaged stock axles. Always apply a small amount of grease to the washer and threads when installing. - Designed and manufactured in Minneapolis, MN USA 7075 T6 Aluminum

Boostinators are hub specific conversions designed to take non-boost hubs and convert them to boost compatibility. Don't toss out that wheelset - Boostinate it.

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

- Colored rim decal kits to personalize your ride - Decals to fit 2 100w 26-inch rims

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 50w 27.5+ rims

- Colored rim decal kits to personalize your ride - Decals to fit two (2) 70w 26-inch rims

Ultra light bolt on thru axle, with a low profile 6mm head for Whisky forks and some others. See other manufacturers specifications for fitment questions. - Thread Length (mm): 12 - Thread Pitch: 1.5 - MT/CX: 125 x 15mm - MTB+: 135 x 15mm - Fat: 198 x 15mm - RD/CX: 120 x 12mm - Rear: 167 x 12mm

Ultra-light, bolt-on thru-axles, with a low-profile 6mm head for use on Whisky forks and others. They are also available in some common rear frame sizes. See manufacturer's specifications for fitment questions. - Thread Length: 12mm

Wheels Manufacturing Axle Spacers help you dial in your hub spacing to ensure correct fit and side-to-side spacing in the rear triangle without having to alter the wheel's dish. - Spacers come in bags of 20

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 126mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 137mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 135mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 146mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese front hubs - Type: Hollow Axle - Threads: 9mm x 1 - Diameter: 9mm - Length: 110mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 155mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many BMX hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 187mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many BMX hubs - Type: Solid Axle - Threads: 9.5mm x 24tpi - Diameter: 9.5mm - Length: 180mm - 1 axle per bag

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

Simply replace the cones on your Supreme front and cassette hubs for a perfect fit without having to spread your dropouts. Available in front, rear, and drive side options. These guards now feature a heat-treated chromo insert for longer life.